350-601 practice questions 391–400

1. Question 391 · 504 in bank

   A Cisco IMC on the Cisco UCS C-Series Server must be configured with VLAN ID 110 and a priority value of 20. Which command set meets these requirements?

   • AServer# scope cimc - Server /cimc # scope vlan - Server /cimc/network # enable vlan Server /cimc/network *# set vlan-id 110 Server /cimc/network *# set vlan-priority 20 Server /cimc/network *# commit
   • BServer# scope cimc - Server /cimc # scope network - Server /cimc/network # set vlan-enabled yes Server /cimc/network *# set vlan-id 110 Server /cimc/network *# set vlan-priority 20 Server /cimc/network *# commit
   • CServer# scope cimc - Server /cimc # scope network - Server /cimc/network # switchport mode trunk Server /cimc/network *# switchport trunk native vlan 110 Server /cimc/network *# spanning-tree portfast Server /cimc/network *# copy run start
   • DServer# scope cimc - Server /cimc # scope network - Server /cimc/network # switchport mode access Server /cimc/network *# switchport access 110 Server /cimc/network *# spanning-tree portfast Server /cimc/network *# copy run start

   Show answer

   Answer: B

   Explanation

   It's correct Server# scope cimc Server /cimc # scope network Server /cimc/network # set vlan-enabled yes Server /cimc/network *# set vlan-id 10 Server /cimc/network *# set vlan-priority 32 Server /cimc/network *# commit Server /cimc/network # show detail https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/sw/cli/config/guide/1-4-1/b_Cisco_UCS_C-Series_CLI_Configuration_Guide_141/b_Cisco_UCS_C-Series_CLI_Configuration_Guide_141_chapter_01000.html#task_F1A505AA52BE41C2A0CE089FCAE4F9D2

   Source: Adapted from community discussion — prospio971

   References

   • Cisco documentation

   Next question

2. Question 392 · 504 in bank

   

   Refer to the exhibit. An engineer must access a Cisco UCS C-Series server KVM from a remote location. The engineer must use the out-of-band interface to access the KYM. Which configuration set meets these requirements?

   • ANIC mode: Shared LOM - VLAN ID: 100
   • BNIC mode: Dedicated - VLAN ID: 101
   • CNIC mode: Dedicated - VLAN state: Disabled
   • DNIC mode: Shared LOM - VLAN state: Disabled

   Show answer

   Answer: C

   References

   • Cisco documentation

   Next question

3. Question 393 · 504 in bank

   A Cisco MDS 9000 Series Switch is configured for SAN Analytics and SAN Telemetry Streaming. An engineer must enable analytics for NVMe on interfaces in the range of fc1/1-12. Due to a large amount of traffic generated in the SAN environment, the data must be collected at regular intervals of 60 seconds from ports fc1/1-12 and then for ports fc1/13-24 for the next 60 seconds. Ports in the range fc1/13-24 were already enabled for analytics. Which set of commands must be used to meet these requirements? A.

   

   B.

   

   C.

   

   D.

   

   This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.

   Show the answer figure

   Answer:

   Explanation

   Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/8_x/config/san_analytics/cisco-mds9000-san-analytics-telemetry-streaming- config-guide-8x/configuring_san_telemetry-streaming.html

   References

   • Cisco documentation

   Next question

4. Question 394 · 504 in bank

   An engineer must deploy a Cisco UCS C-Series Server with a single VIC 1455 integrated into a Cisco UCS Manager cluster. Two fiber connections are available, and the deployment has no fabric extenders. Which set of actions accomplishes this goal?

   • AReset the system using Cisco IMC to its factory default settings. Attach VIC port 1 and 3 to Fabric Interconnects.
   • BConfigure VIC attached ports as Uplink ports on fabric interconnects. Insert 1000Base-T RJ45 SFP in VIC port 1 and 3.
   • CReset the system using Cisco IMC to its factory default settings. Insert 1000Base-T RJ45 SFP in VIC port 1 and 3.
   • DConfigure VIC attached ports as Uplink ports on fabric interconnects. Attach VIC port 1 and 3 to Fabric Interconnects.

   Show answer

   Answer: A

   References

   • Cisco documentation

   Next question

5. Question 395 · 504 in bank

   An engineer must configure device aliases for a Cisco MDS 9000 Series Switches-based SAN fabric. The configuration must meet these requirements: • The engineer must be prompted before the changes are committed to the database. • Pending changes must be explicitly displayed on the console. Which command accomplishes this task?

   • Adevice-alias enhanced
   • Bdevice-alias commit
   • Cdevice-alias confirm-commit
   • Ddevice-alias distribute diffs-only

   Show answer

   Answer: C

   Explanation

   C is correct: If the device-alias confirm-commit command is enabled, on committing the pending database, the pending-diff is displayed on the console and user is prompted for Yes or No

   Source: Adapted from community discussion — crooks_1988

   Next question

6. Question 396 · 504 in bank

   

   Refer to the exhibit. An engineer configures an FCoE connection between a Cisco UCS and a Cisco Nexus 9000 Series Switch. The UCS FI-A connects to the Nexus switch using interface e1/12. All relevant configurations have been completed on the Nexus switch to support FCoE deployment. Which action must be taken on Cisco UCS Manager to complete the configuration?

   • ATrunk VLAN 500 on interface e1/12.
   • BCreate a Virtual Fibre Channel Interface.
   • CChange the Transport Type to FCoE.
   • DConfigure an FCoE uplink interface.

   Show answer

   Answer: D

   References

   • Cisco documentation

   Next question

7. Question 397 · 504 in bank

   Select 2

   An engineer configures a storage environment for a customer with high-security standards. The secure environment is configured in VSAN 50. The customer wants to maintain a configuration and active databases and prevent unauthorized switches from joining the fabric. Additionally, the switches must prevent rogue devices from connecting to their ports by automatically learning the WWPNs of the ports connected to them for the first time. Which two configuration sets must be used to meet these requirements? (Choose two.)

   • Afcsp enable fcsp auto-active
   • Bport-security enable port-security activate vsan 50
   • Cclear fabric-binding activate vsan 50 fabric-binding activate vsan 50
   • Dfcsp dhchap hash md5 sha1
   • Efabric-binding activate vsan 50 force

   Show answer

   Answer: BE

   References

   • Cisco documentation

   Next question

8. Question 398 · 504 in bank

   An engineer must configure a Cisco MDS 9000 Series Switch to store generated log messages to a file. The file must store logs of the severity of "warning" and above, and the file size must not exceed 20,000 bytes. Which command accomplishes this task?

   • Alogging logfile LogFile 5 size 2000
   • Blogging logfile messages 2 size 2500
   • Clogging logfile Local 4 size 20000
   • Dlogging logfile Logs 3 size 160000

   Show answer

   Answer: C

   Next question

9. Question 399 · 504 in bank

   

   Refer to the exhibit. An engineer must create a Bash script to run in the Cisco NX-OS Guest Shell. The script must loop through the available namespaces and output all registered interfaces. Which code snippet completes the script?

   • Achvrf "$ns";
   • Becho "$ns";
   • Cifconfig "$ns";
   • Dvrfinfo"$ns";

   Show answer

   Answer: A

   Explanation

   From the link provided by JCGO some explanation for this: "The Guestshell has access to the Linux network interfaces used to represent the management and data ports of the switch. Typical Linux methods and utilities like ifconfig and ethtool can be used to collect counters. When an interface is placed into a VRF in the NX-OS CLI, the Linux network interface is placed into a network namespace for that VRF. The name spaces can be seen at /var/run/netns and the ip netns utility can be used to run in the context of different namespaces. A couple of utilities, chvrf and vrfinfo , are provided as a convenience for running in a different namespace and getting information about which namespace/vrf a process is running in. "

   Source: Adapted from community discussion — camelw

   References

   • Cisco documentation

   Next question

10. Question 400 · 504 in bank

    

    Refer to the exhibit. A network engineer is using tcpdump to capture a snapshot of OSPF-retated traffic on a specific Cisco NX-OS switch port. For security reasons, the capture must be taken using an embedded container that is already deployed on the Cisco Nexus device. Which command completes the script?

    • Aguestshell-bash
    • Brun guestshell
    • Crun bash
    • Dguestshell

    Show answer

    Answer: D

    Explanation

    D is the answer 8kv91#guestshell [guestshell@guestshell ~]$ sudo yum update [guestshell@guestshell bootflash]$ sudo ip netns exec management ping 10.28.38.48 PING 10.28.38.48 (10.28.38.48) 56(84) bytes of data. 64 bytes from 10.28.38.48: icmp_seq=1 ttl=48 time=76.5 ms

    Source: Adapted from community discussion — Arch_Angel

    References

    • Cisco documentation

    Next question

Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page

350-601 practice, question 391. 504 questions available.