Question 381 · 504 in bank
Select 2Which two actions are needed to configure a single Cisco APIC controller for Cisco ACI fabric for the first time? (Choose two.)
Show answer
Answer: CD
350-601ProfessionalCiscoAll questions freePage 39 of 51
350-601 practice questions 381–390
Implementing and Operating Cisco Data Center Core Technologies (DCCOR)504 questions across 51 pages are complete and free, with no account or card.
Official study references
504 questions in this bank
Free access · progress saved on this device
Question 382 · 504 in bank
A network architect wants to propose a scalable network monitoring solution in which data is repeatedly acquired from network devices. The solution must use a push model and provide close to real-time access to operational data. Which technology must be used to meet these requirements?
Show answer
Answer: D
Question 383 · 504 in bank
An engineer implements an Application Performance Monitoring (APM) solution. The solution runs in a vSphere infrastructure where the vSwitch support for promiscuous mode is disabled for security reasons. As a result, the final implementation must receive a copy of bidirectional traffic to a load balancer that is connected to a Cisco Nexus 93108 Series Switch. The APM solution supports GRE encapsulated traffic. Which configuration must be applied to the switch to meet this requirement?
Show answer
Answer: C
Explanation
Agree with C, snippet of a ERSPAN config at source: monitor session 1 type erspan-source erspan-id 2 vrf TEST destination ip 1.1.1.1 source vlan 12 both no shut
Source: Adapted from community discussion — crooks_1988
References
Question 384 · 504 in bank
What is a feature of an electronic programmable logic device upgrade on a Cisco MDS 9000 Series Switch?
Show answer
Answer: A
Question 385 · 504 in bank
DRAG DROP -
Refer to the exhibit. An engineer implements a dynamically negotiated LACP port channel on SW1. The port channel members must be configured as active/standby ports with Eth1/2 as active and Eth1/1 as standby. The Eth1/1 interface is configured with default priority. Drag and drop the code snippets from the right onto the blanks in the code on the left to complete the Eth1/2 interface configuration for SW1. Not all code snippets are used.
This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.
Show the answer figure
Question 386 · 504 in bank
Select 2An engineer must configure a new Cisco UCS B-Series infrastructure with a Cisco 5108 chassis. The configuration must meet these requirements: • The setup must use aggregation between Cisco UCS Fabric Interconnects and I/O modules. • The implementation requires four 10 GbE connections per I/O module. • The Cisco UCS Fabric Interconnects must support uplinks of different speeds for future expansion. Which two steps must be taken to meet these requirements? (Choose two.)
Show answer
Answer: AD
Explanation
A adn D. https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/141/UCSM_GUI_Configuration_Guide_141_chapter12.html 1) reacknowlenge the chassis after discovery 2) links should be aggregated at future. Provided answers incorrect, they are related to uplinks, not downlonks to IOM's
Source: Adapted from community discussion — JCGO
References
Question 387 · 504 in bank
An engineer must replace a defective fabric interconnect with the same model. The system must be restored, including the database of locally created users. The equivalent Cisco UCS Manager software version must be used. Which backup type must be used to meet these requirements?
Show answer
Answer: A
References
Question 388 · 504 in bank
Which Cisco UCS firmware reboot policy must be used in the maintenance policy to prevent the server firmware from upgrading automatically and wait for user input before proceeding?
Show answer
Answer: D
Question 389 · 504 in bank
An engineer configures user authentication on Cisco UCS Manager to ensure that the user and roles can be saved on the external server and secured using authentication. Which set of actions meets these requirements?
Show answer
Answer: C
Question 390 · 504 in bank
An engineer must upgrade the server firmware for which the service profile is configured with a host firmware package. Which action must be taken to accomplish this goal?
Show answer
Answer: C
Explanation
Agree with C: You can use firmware packages in service profiles to upgrade the server and adapter firmware, including the BIOS on the server, by defining a host firmware policy and including it in the service profile associated with a server.
Source: Adapted from community discussion — crooks_1988
Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page
350-601 practice, question 381. 504 questions available.
About this question bank
Version 1.0.0. How we source questions