350-601 practice questions 351–360

1. Question 351 · 504 in bank

   Select 2

   An engineer performs a set of configuration changes for the vPC domain using Session Manager. Which two commands are used to verify the configuration and apply the device changes when no errors are returned? (Choose two.)

   • Acommit
   • Bverify
   • Capply
   • Dcheckpoint
   • Ewrite

   Show answer

   Answer: AB

   Explanation

   Verifying a Session - To verify a session, use the following command in session mode. Committing a Session - To commit a session, use the following command in session mode. Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/CLIConfigurationGuide/sm_rollback.html

   

   Next question

2. Question 352 · 504 in bank

   Which event is expected during direct upgrade of Cisco UCS Manager firmware?

   • AThe I/O Module reboots immediately after the firmware is activated.
   • BData traffic is disrupted for a single fabric interconnect setup.
   • CIPMI polling is interrupted.
   • DAll users logged in to the UCSM are logged out, and their sessions end.

   Show answer

   Answer: D

   Explanation

   According to cisco: Outage Impacts of Direct Firmware Upgrades A firmware upgrade to Cisco UCS Manager causes the following disruptions: Cisco UCS Manager GUI—All users logged in to Cisco UCS Manager GUI are logged out and their sessions ended. Any unsaved work in progress is lost. Cisco UCS Manager CLI—All users logged in through telnet are logged out and their sessions ended.

   Source: Adapted from community discussion — warCZert

   Next question

3. Question 353 · 504 in bank

   An engineer must migrate a Cisco UCS C-Series server from Cisco SingleConnect to direct connect integration mode. The Cisco UCS Manager Rack Server Discovery Policy and Rack Management Connection Policy are set to Immediate and Auto-Acknowledge. Which set of steps accomplishes this task?

   • ADisconnect the cables from the FEX. Connect the cables to server ports on the fabric interconnect. Reacknowledge the server.
   • BDisconnect the cables from the FEX. Connect the cables to appliance ports on the fabric interconnect. Reacknowledge the server.
   • CDisconnect the cables from the FEX. Connect the cables to server ports on the fabric interconnect. Reset the Cisco IMC of the server.
   • DDisconnect the cables from the FEX. Connect the cables to appliance ports on the fabric interconnect. Reset the Cisco IMC of the server.

   Show answer

   Answer: A

   Explanation

   Cisco Doc: Step 1 Configure the server ports on the FI. Step 2 Disconnect the cables from the FEX and connect them to the configured server ports on Fabric Interconnect. Step 3 On the Cisco UCS Manager GUI, right click the server, from the pop-up menu, select Recover Server or Server Maintenance. Step 4 Click Re-acknowledge and select OK. This will cause server reboot.

   Source: Adapted from community discussion — warCZert

   Next question

4. Question 354 · 504 in bank

   What is a benefit of Cisco HyperFlex All-Flash Stretched cluster deployment as compared to All-HDD Stretched cluster deployment?

   • Alower number of IOPS
   • Bhigher number of IOPS
   • Clower cost
   • Dhigher cost

   Show answer

   Answer: B

   Next question

5. Question 355 · 504 in bank

   DRAG DROP - Drag and drop the NAS and NFS concepts from the left onto the definitions on the right.

   

   This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.

   Show the answer figure

   Answer: See figure below

   Explanation

   Provided solution is incorrect: it should be NFS The protocol is regularly used on Linux and Unix systems The vendor-agnostic protocol is supported on any hardware and OS NAS Data storage and file sharing requests are sent and received Software is deployed on a lighweight OS that is embedded in the hardware

   Source: Adapted from community discussion — Scheldon

   

   Next question

6. Question 356 · 504 in bank

   Which device alias database is shown by this output? switch# show device-alias database device-alias name SampleName pwwn 24:40:00:e7:09:0b:27:56

   • Ainactive database
   • Beffective database
   • Cpending database
   • Dzoning database

   Show answer

   Answer: B

   Explanation

   Device Alias Configuration Verification You can view device alias information by using the show device-alias command. See the following examples. Displays All Configured Device Aliases from the Effective Database switch# show device-alias database device-alias name SampleName pwwn 21:00:00:e0:8b:0b:66:56 device-alias name x pwwn 21:01:00:e0:8b:2e:80:93 Total number of entries = 2 https://www.cisco.com/c/en/us/td/docs/dcn/mds9000/sw/9x/configuration/fabric/cisco-mds-9000-nx-os-fabric-configuration-guide-9x/distributing_device_alias_services.html

   Source: Adapted from community discussion — RFV147

   References

   • Cisco documentation
   • Cisco documentation

   Next question

7. Question 357 · 504 in bank

   

   Refer to the exhibit. Server1 is connected to a Cisco Nexus 9000 Series Switch via a 1-Gb port channel. The storm control is applied to the Eth0 device with a zero percent value. What does the switch do to traffic that traverses the switch interfaces during the streaming window that exceeds the bandwidth of the interfaces?

   • Asuppresses all traffic
   • Bforwards all traffic
   • Cdrops all of the excess traffic
   • Dforwards half of the traffic

   Show answer

   Answer: A

   Explanation

   agree but they are asking about the traffic that exceeds the bw of the interfaces and I dont see the relation to storm control there. That traffic is either buffered or dropped.

   Source: Adapted from community discussion — Huberttheman

   References

   • Cisco documentation
   • Cisco documentation
   • Cisco documentation

   Next question

8. Question 358 · 504 in bank

   Which storage solution operates at the file level and contains its own native lightweight operating system on simplified hardware?

   • ANAS
   • BSAN
   • Cunified fabric
   • Dstandard file server

   Show answer

   Answer: A

   Next question

9. Question 359 · 504 in bank

   Which component becomes unavailable for a maximum of 80 seconds during a nondisruptive Cisco NX-OS upgrade?

   • Asupervisor module
   • Bdefault VSAN
   • Ccontrol plane
   • Ddata plane

   Show answer

   Answer: C

   Next question

10. Question 360 · 504 in bank

    

    Refer to the exhibit. An engineer must monitor all LAN traffic on Fabric A from a blade server. Which source should be configured in the test-span monitor session to complete this task?

    • Aall uplink FCoE ports
    • Ball vNICs from the service profile that correspond to this server
    • Call uplink Ethernet ports
    • Dall vHBAs from the service profile that correspond to this server

    Show answer

    Answer: B

    Explanation

    Reference: https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/141/UCSM_GUI_Configuration

    Source: Adapted from community discussion — mauchi

    References

    • Cisco documentation

    Next question

Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page

350-601 practice, question 351. 504 questions available.