Question 301 · 1334 in bank
Which physical component is distributed among multiple virtual machines running on the same hypervisor?
Show answer
Answer: D
Cisco Certified Network Associate (CCNA)1,334 questions across 134 pages are complete and free, with no account or card.
1334 questions in this bank
Free access · progress saved on this device
Which physical component is distributed among multiple virtual machines running on the same hypervisor?
Answer: D
What is the default behavior of a Layer 2 switch when a frame with an unknown destination MAC address is received?
Answer: C
Sometimes called BUM traffic - Broadcast, Unknown Unicast, Multicast. These forms of traffic are "flooded" out all ports except the port the packet was received on.
Source: Adapted from community discussion — therandman
Refer to the exhibit. Configurations for the switch and PCs are complete. Which configuration must be applied so that VLANs 2 and 3 communicate back and forth?
Answer: B
B is correct. Question gave 3 hints to work on. (RoS, VLAN 3, and /23) RoS require matching VLAN ID which is 3 and /23 = 254. So dot1Q=3 and 255.255.254.0 = B Hope this help
Source: Adapted from community discussion — HMaw
DRAG DROP - Drag and drop the characteristic from the left onto the IPv6 address type on the right.

This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.
Answer: See figure below
What causes a port to be placed in the err-disabled state?
Answer: B
B. port security violation When port security is configured on a switch port and a security violation occurs (such as an unauthorized MAC address being detected), the port can be placed into the err-disabled state as a protective measure. This state effectively shuts down the port and prevents any traffic from passing through until the issue is resolved and the port is manually re-enabled. Other incorrect Options: - A. the shutdown command on a port will disable the port, but it does not place it in the err-disabled state. The port is administratively down but can be brought back up with the no shutdown command. - C. nothing plugged into the port: does not cause it to be placed in the err-disabled state. The port will simply be in an "up/down" or "notconnected" state. - D. Latency is typically a performance issue and not a reason for disabling a port.
Source: Adapted from community discussion — KAM2023

Refer to the exhibit. The IPv6 address for the LAN segment on router R2 must be configured using the EUI-64 format. When configured which ipv6 address is produced by the router?
Answer: B
13:B0:AB:CC:00:01 Convertion process: 1) Take the mac address: for example 13:B0:AB:CC:00:01 2) Throw ff:fe in the middle: 13:B0:AB:ff:fe:CC:00:01 3) Reformat to IPv6 notation 13B0:ABff:feCC:0001 4) Convert the first octet from hexadecimal to binary: 13 -> 00010011 5) Invert the bit at index 6 (counting from 0): 00010011 -> 00010001 6) Convert octet back to hexadecimal: 00010001 -> 11 7) Replace first octet with newly calculated one: 11B0:ABff:feCC:0001 8) Prepend the link-local prefix: fe80::11B0:ABff:feCC:1
Source: Adapted from community discussion — KuyaErik101
Refer to the exhibit. Which switch becomes the root bridge?
Answer: A
What is represented by the word "switch" within this JSON schema?
Answer: A
How does encryption protect the wireless network?
Answer: B
DRAG DROP - Drag and drop the characteristic from the left onto the cable type on the right.

This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.
Answer: See figure below

Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page
200-301 practice, question 301. 1334 questions available.
Version 1.0.0. How we source questions