Implementing and Operating Cisco Data Center Core Technologies (DCCOR)504 questions across 51 pages are complete and free, with no account or card.
504 questions in this bank
Free access · progress saved on this device
Which service profile is affected if the default host firmware policy in Cisco UCS Manager is changed?
Answer: C
If you update the default host firmware package, you might cause the upgrade of firmware on unassociated servers and on servers with associated service profiles that do not include a host firmware package.
Source: Adapted from community discussion — huvilla
An engineer is implementing Cisco Intersight in a secure environment. The environment must use LDAP directory service and ensure information integrity and confidentiality. Which two steps must be taken to implement the solution? (Choose two.)
Answer: BC
Enable Encryption—You must enable Encryption to secure the communication over the LDAP server. If encryption is enabled, a trusted root certificate has to be added. For more information, see Adding Certificates.
Source: Adapted from community discussion — g_kuchima
Due to a domain name change at a customer site, a Cisco UCS cluster must be renamed. An engineer must recommend a solution to ensure that the Cisco UCS Manager is available over HTTPS. Which action accomplishes this goal?
Answer: A
An engineer needs to make an XML backup of Cisco UCS Manager. The backup should be transferred using an authenticated and encrypted tunnel, and it should contain all system and service profiles configuration. Which command must be implemented to meet these requirements?
Answer: B
Refer to the exhibit.
What is configured as a result of running these commands?
Answer: B
The ג€ip verify unicast source reachable-via rxג€ command enables Unicast RPF in strict mode. To enable loose mode, administrators can use the any option to enforce the requirement that the source IP address for a packet must appear in the routing table. Reference: https://www.examtopics.com/discussions/cisco/view/62014-exam-350-601-topic-1-question-13-discussion/
Source: Adapted from community discussion — MaxG
A network architect considers a Cisco HyperFlex design solution for a company. The proposed solution is for a virtual environment that is not performance- sensitive, but the solution must have high storage capacity and a low cost. Which Cisco HyperFlex storage configuration should be used?
Answer: A
Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/UCS_CVDs/hx_4_vsi_vmware_esxi.html
The Cisco Nexus 5600 Series Switch experiences occasional packet drops on interface ethernet 1/16. An engineer wants to implement a SPAN session to investigate the issue further. The network analyzer to which the packets must be directed is located on interface 1/3. The analyzer is limited on disk space available for traffic capture, so the Cisco Nexus Switch should send only the relevant data. Which two command sets configure the SPAN session that meets these requirements? (Choose two.) A.
B.
C.
D.
E.
This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.
Answer:
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus6000/sw/system_management/6x/b_6k_System_Mgmt_Config_6x/ b_6k_System_Mgmt_Config_602N11_chapter_01111.pdf
An engineer needs to monitor ingress traffic that arrives at interface Ethernet 1/3 that belongs to a Cisco Nexus 5600 Series Switch. The traffic analyzer machine located at interface Ethernet 1/5 is already monitoring other production, and the traffic analyzer must not be impacted by the traffic captured from the interface Eth1/3. The operations team allocated a traffic budget for the new monitoring session of 1 Gbps to meet this requirement. Which set of commands configures the SPAN session? A.
B.
C.
D.
This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.
Answer:
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5600/sw/system_management/7x/b_5600_System_Mgmt_Config_7x/ b_6k_System_Mgmt_Config_7x_chapter_01110.html
Source: Adapted from community discussion — MaxG
An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect. Which backup type must be selected to meet these requirements?
Answer: C
Reference: https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/141/UCSM_GUI_Configuration_Guide_141_chapter43.html
Source: Adapted from community discussion — MaxG
An engineer creates a service profile in Cisco UCS Manager and must assign a policy that reboots blades when changes are applied. The changes must be applied only after user acknowledgment. Which two policies must be configured to meet these requirements? (Choose two.)
Answer: AE
Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Admin-Management/3-1/ b_Cisco_UCS_Admin_Mgmt_Guide_3_1/b_Cisco_UCS_Admin_Mgmt_Guide_3_1_chapter_01011.html
Source: Adapted from community discussion — malkovitch
Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page
350-601 practice, question 31. 504 questions available.
Version 1.0.0. How we source questions