300-620 practice questions 71–80

1. Question 71 · 340 in bank

   Select 2

   What are two requirements for the IPN network when implementing a Multi-Pod ACI fabric? (Choose two.)

   • AEIGRP routing
   • BPIM ASM multicast routing
   • CBGP routing
   • DVLAN ID 4
   • EOSPF routing

   Show answer

   Answer: BE

   Next question

2. Question 72 · 340 in bank

   Select 2

   A Solutions Architect is asked to design two data centers based on Cisco ACI technology that can extend L2/L3, VXLAN, and network policy across locations. ACI Multi-Pod has been selected. Which two requirements must be considered in this design? (Choose two.)

   • AACI underlay protocols, i.e. COOP, IS-IS and MP-BGP, spans across pods. Create QoS policies to make sure those protocols have higher priority.
   • BA single APIC Cluster is required in a Multi-Pod design. It is important to place the APIC Controllers in different locations in order to maximize redundancy and reliability.
   • CACI Multi-Pod requires an IP Network supporting PIM-Bidir.
   • DACI Multi-Pod does not support Firewall Clusters across Pods. Firewall Clusters should always be local.
   • EMulti-Pod requires multiple APIC Controller Clusters, one per pod. Make sure those clusters can communicate to each other through a highly available connection.

   Show answer

   Answer: BC

   Next question

3. Question 73 · 340 in bank

   An engineer configures a Multi-Pod system with the default getaway residing outside of the ACI fabric for a bridge domain. Which setting should be configured to support this requirement?

   • Adisable Limit IP Learning to Subnet
   • Bdisable IP Data-plane Learning
   • Cdisable Unicast Routing
   • Ddisable Advertise Host Routes

   Show answer

   Answer: C

   Next question

4. Question 74 · 340 in bank

   What do Pods use to allow Pod-to-Pod communication in a Cisco ACI Multi-Pod environment?

   • Aover Layer 3 directly connected back-to-back spines
   • Bover Layer 3 Out connectivity via border leafs
   • Cover Layer 3 IPN connectivity via border leafs
   • Dover Layer 3 IPN connectivity via spines

   Show answer

   Answer: D

   Next question

5. Question 75 · 340 in bank

   An engineer must advertise a selection of external networks learned from a BGP neighbor into the ACI fabric. Which L3Out subnet configuration option creates an inbound route map for route filtering?

   • AExternal Subnets for the External EPG
   • BShared Route Control Subnet
   • CImport Route Control Subnet
   • DShared Security Import Subnet

   Show answer

   Answer: C

   Next question

6. Question 76 · 340 in bank

   An engineer must set up a Cisco ACI fabric to send Syslog messages related to hardware events, such as chassis line card failures. The messages should be sent to a dedicated Syslog server. Where in the Cisco APIC should the policy be configured to meet this requirement?

   • Auni/tn-common/monepg-default
   • Buni/infra/monifra-default
   • Cuni/fabric/monfab-default
   • Duni/fabric/moncommon

   Show answer

   Answer: C

   Next question

7. Question 77 · 340 in bank

   The existing network and ACI fabric have been connected to support workload migration. Servers will physically terminate at the Cisco ACI, but their gateway must stay in the existing network. The solution needs to adhere to Cisco’s best practices. The engineer started configuring the relevant Bridge Domain and needs to complete the configuration. Which group of settings are required to meet these requirements?

   • AL2 Unknown Unicast: Hardware Proxy L3 Unknown Multicast Flooding: Flood Multi Destination Flooding: Flood in BD ARP Flooding: Enable -
   • BL2 Unknown Unicast: Flood - L3 Unknown Multicast Flooding: Flood Multi Destination Flooding: Flood in BD ARP Flooding: Enable -
   • CL2 Unknown Unicast: Flood - L3 Unknown Multicast Flooding: Optimize Flood Multi Destination Flooding: Flood in BD ARP Flooding: Disable -
   • DL2 Unknown Unicast: Hardware Proxy L3 Unknown Multicast Flooding: Optimize Flood Multi Destination Flooding: Flood in BD ARP Flooding: Disable

   Show answer

   Answer: B

   Next question

8. Question 78 · 340 in bank

   An engineer must implement management policy and data plane separation in the Cisco ACI fabric. Which ACI object must be created in Cisco APIC to accomplish this goal?

   • AApplication profile
   • BTenant
   • CContract
   • DBridge domain

   Show answer

   Answer: B

   Next question

9. Question 79 · 340 in bank

   An engineer is implementing a Cisco ACI environment that consists of more than 20 servers. Two of the servers support only Cisco Discovery Protocol with no other link discovery protocol. The engineer wants the servers to be discovered automatically by the Cisco ACI fabric when connected. Which action must be taken to meet this requirement?

   • ACreate an override policy that enables Cisco Discovery Protocol after LLDP is enabled in the default policy group.
   • BConfigure a higher order interface policy that enables Cisco Discovery Protocol for the interface on the desired leaf switch.
   • CConfigure a lower order policy group that enables Cisco Discovery Protocol for the interface on the desired leaf switch.
   • DCreate an interface profile for the interface that disables LLDP on the desired switch that is referenced by the interface policy group.

   Show answer

   Answer: A

   Next question

10. Question 80 · 340 in bank

    An engineer wants to monitor all configuration changes, threshold crossing, and link-state transitions in a Cisco ACI fabric. Which action must be taken to receive the required messages?

    • AAdd Faults and Events to the monitor policy.
    • BAdd Session Logs and Audit Logs to the monitor policy.
    • CInclude Audit Logs and Events in the Syslog source policy.
    • DInclude Events and Session Logs in the Syslog source policy.

    Show answer

    Answer: C

    Next question

Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page

300-620 practice, question 71. 340 questions available.