2V0-41.24 practice questions 61–70

1. Question 61 · 83 in bank

   Which table on an ESXi host is used to determine the location of a particular workload for a frame-forwarding decision?

   • ARouting Table
   • BARP Table
   • CTEP Table
   • DMAC Table

   Show answer

   Answer: D

   Next question

2. Question 62 · 83 in bank

   What is the most restrictive NSX built-in role which will allow a user to apply configuration changes on an NSX Edge?

   • ANetwork Engineer
   • BCloud Service Administrator
   • CNSX Administrator
   • DNetwork Operator

   Show answer

   Answer: A

   Next question

3. Question 63 · 83 in bank

   Refer to the exhibit. An administrator would like to change the private IP address of the NAT VM 172.16.101.11 to a public address of 80.80.80.1 as the packets leave the NAT-Segment network. Which type of NAT solution should be implemented to achieve this?

   

   • ANAT64
   • BReflexive NAT
   • CDNAT
   • DSNAT

   Show answer

   Answer: D

   Next question

4. Question 64 · 83 in bank

   Which command is used to display the network configuration of the Tunnel Endpoint (TEP) IP on a bare metal transport node?

   • Adebug
   • Btcpdump
   • Ctcpconfig
   • Difconfig

   Show answer

   Answer: D

   Next question

5. Question 65 · 83 in bank

   Which VPN type must be configured before enabling an L2VPN?

   • APolicy-based IPSec VPN
   • BPort-based IPSec VPN
   • CSSL-based IPSec VPN
   • DRoute-based IPSec VPN

   Show answer

   Answer: D

   Next question

6. Question 66 · 83 in bank

   What should an NSX administrator check to verify that VMware Identity Manager integration is successful?

   • AFrom the NSX UI the status of the VMware Identity Manager Integration must be “Enabled”.
   • BFrom the NSX CLI the status of the VMware Identity Manager Integration must be “Configured”.
   • CFrom VMware Identity Manager the status of the remote access application must be green.
   • DFrom the NSX UI the URI in the address bar must have “local=false” part of it.

   Show answer

   Answer: A

   Next question

7. Question 67 · 83 in bank

   Select 3

   Which three DHCP Services are supported by NSX? (Choose three.)

   • AGateway DHCP
   • BSegment DHCP
   • CDHCP Relay
   • DPort DHCP per VNF
   • EVRF DHCP Server

   Show answer

   Answer: ABC

   Explanation

   D. Port DHCP per VNF: This is not a valid DHCP service in NSX. DHCP is not configured per VNF port. E. VRF DHCP Server: NSX doesn't explicitly support a "VRF DHCP Server." While VRFs are supported for routing, DHCP services are associated with gateways or segments, not VRFs.

   Source: Adapted from community discussion — electro165

   Next question

8. Question 68 · 83 in bank

   Which choice is a valid insertion point for North-South network introspection?

   • AHost Physical NIC
   • BTier-0 gateway
   • CGuest VM vNIC
   • DPartner SVM

   Show answer

   Answer: B

   Next question

9. Question 69 · 83 in bank

   Which of the following settings must be configured in an NSX environment before enabling stateful active-active SNAT?

   • ATier-1 gateway in active-standby mode
   • BA Punting Traffic Group for the NSX Edge uplinks
   • CAn Interface Group for the NSX Edge uplinks
   • DTier-1 gateway in distributed only mode

   Show answer

   Answer: C

   References

   • docs.vmware.com documentation

   Next question

10. Question 70 · 83 in bank

    An NSX administrator is reviewing syslog and notices that Distributed Firewall Rules hit counts are not being logged. What could cause this issue?

    • AZero Trust Security is not enabled.
    • BSyslog is not configured on the NSX Manager.
    • CSyslog is not configured on the ESXi transport node.
    • DDistributed Firewall Rule logging is not enabled.

    Show answer

    Answer: D

    Next question

Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page

2V0-41.24 practice, question 61. 83 questions available.