Implementing Cisco SD-WAN Solutions (ENSDWI)382 questions across 39 pages are complete and free, with no account or card.
382 questions in this bank
Free access · progress saved on this device
What is the procedure to upgrade all Cisco SD-WAN devices to a recent version?
Answer: B
Reference: https://community.cisco.com/t5/networking-documents/cisco-sd-wan-software-upgrade-best-practices/ta-p/4101848
What prohibits deleting a VNF image from the software repository?
Answer: B
Correct answer is B, you can look at the following link for reference: https://www.cisco.com/c/en/us/td/docs/routers/sdwan/configuration/Monitor-And-Maintain/monitor-maintain-book/maintain.html#task_hbp_kmd_ffb "If the VNF image is referenced by a service chain, it can’t be deleted."
Source: Adapted from community discussion — MiraGod
An organization requires the use of integrated preventative engines, exploit protection, and the most updated and advanced signature-based antivirus with sandboxing and threat intelligence to stop malicious attachments before they reach users and get executed. Which Cisco SD-WAN solution meets the requirements?
Answer: B
An enterprise needs DIA on some of its branches with a common location ID: A042:B49C:D02E::72. Which WAN Edge configuration meets the requirement?
Answer: D
D is correct. Enable NAT on the transport interface. VPN 0 Create static route in the service VPN to direct traffic out of the NATed transport.
Source: Adapted from community discussion — ChrisCCNA
What is the minimum Red Hat Enterprise Linux operating system requirement for a Cisco SD-WAN controller deployment via KVM?
Answer: A
DRAG DROP - Drag and drop the components from the left onto the corresponding Cisco NFV Infrastructure Building Blocks on the right. Not all options are used. Select and Place:
This is an interactive task on the real exam — a drag-and-drop, hotspot or ordering question. There is nothing to select here, so the answer is shown below for reference.
Which two metrics must a cloud Edge router use to pick the optimal path for a SaaS application reachable via a gateway site? (Choose two.)
Answer: AB
I think the correct answer should be AB. -The gateway vEdge uses HTTP to obtain SaaS application performance information - The client vEdge will use BFD over the IPSec tunnel to the gateway site to obtain client>gateway path performance information https://www.cisco.com/c/dam/en/us/td/docs/solutions/CVD/SDWAN/CVD-SD-WAN-Cloud-onRamp-for-SaaS-Deployment-Guide-2018JUL.pdf
Source: Adapted from community discussion — Kimimoto
Which destination UDP port is used by WAN Edge router to make a DTLS connection with vBond Orchestrator?
Answer: C
An administrator is configuring the severity level on the vManage NMS for events that indicate that an action must be taken immediately. Which severity level must be configured?
Answer: B
I'm going with B as well "In the Severity drop-down, select the event severity level. Events generated by Cisco SD-WAN devices are collected by vManage NMS and classified as: Critical—indicates that action needs to be taken immediately. Major—indicates that the problem needs to be looked into but is not critical enough to bring down the network. Minor—is informational only." source(search 'Set Event Filters'): https://www.cisco.com/c/en/us/td/docs/routers/sdwan/vManage-Help/xe-17-vedge-20/b-vmanage-help/m-help-monitor.html#c_Events_12335.xml
Source: Adapted from community discussion — M_Ryu
An engineer must automate certificate signing through Cisco. Which vManage configuration achieves this task?
Answer: C
Automated certificate signing through Cisco Systems With this option, certificate signing requests are automatically sent to the Cisco PnP cloud service where the certificate is signed. The vManage then automatically retrieves the certificate and installs it. A DNS server needs to be configured to resolve the hostname, cloudsso.cisco.com and subsequently, apx.cisco.com. The vManage needs to reach both servers on TCP port 443. Note that this option requires vManage version 19.1 or higher (19.2 or higher is recommended) and also requires that Smart Account credentials are configured before this certificate option can be configured. Procedure 1: Verify Cisco server reachability 1. Ensure that a DNS server is defined for VPN 0 on vManage via SSH or console: config terminal vpn 0 dns 208.67.222.222 primary commit and-quit
Source: Adapted from community discussion — Neil_Neo234
Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page
300-415 practice, question 81. 382 questions available.
Version 1.0.0. How we source questions
