Implementing Cisco Enterprise Network Core Technologies (ENCOR)1,003 questions across 101 pages are complete and free, with no account or card.
1003 questions in this bank
Free access · progress saved on this device
Which activity requires access to Cisco DNA Center CLI?
Answer: D
Stop guessing ESPECIALLY without backing your answer with some sort of credenible facts or links. We pay for GOOD information... remember that.
Source: Adapted from community discussion — CCNPWILL
Refer to the exhibit. An engineer must configure an ERSPAN tunnel that mirrors traffic from Linux1 on Switch1 to Linux2 on Switch2. Which command must be added to the destination configuration to enable the ERSPAN tunnel?
Answer: B
I think this question is wrong. The destination address is pointing to sw2 loop back when it’s suppose to be the Linux box. Shutdown is not configured either.
Source: Adapted from community discussion — x3rox
Refer to the exhibit.
Router1 is currently operating as the HSRP primary with a priority of 110. Router1 fails and Router2 takes over the forwarding role. Which command on Router1 causes it to take over the forwarding role when it returns to service?
Answer: B
What are two characteristics of Cisco SD-Access elements? (Choose two.)
Answer: AD
https://www.cisco.com/c/en/us/td/docs/solutions/CVD/Campus/cisco-sda-design-guide.html#Border_Node The fabric border nodes serve as the gateway between the SD-Access fabric site and the networks external to the fabric. https://www.cisco.com/c/en/us/td/docs/solutions/CVD/Campus/cisco-sda-design-guide.html#Control_Plane_Node The control plane node enables the following functions: Host tracking database — a central repository of Endpoint ID to Routing Locator (EID-to-RLOC) bindings
Source: Adapted from community discussion — HungarianDish_111
When is an external antenna used inside a building?
Answer: C
Refer to the exhibit. R1 and R2 are directly connected, but the BGP session does not establish. Which action must be taken to build an eBGP session?
Answer: A
Because if you look at the show ip bgp summary output on R2, it clearly shows neighbor 192.168.12.1 is admin down. That means under R2 BGP process, neighbor 192.168.12.1 has been shut down.
Source: Adapted from community discussion — bendarkel
A company requires a wireless solution to support its main office and multiple branch locations. All sites have local Internet connections and a link to the main office for corporate connectivity. The branch offices are managed centrally. Which solution should the company choose?
Answer: B
Which QoS feature uses the IP Precedence bits in the ToS field of the IP packet header to partition traffic into different priority levels?
Answer: A
It is tricky and actually stupid (Cisco style I guess...) as classification and marking go together and one is useless without another. The traffic needs to be classified first so it could ba marked. The IPP bits are actually used to mark something which is in line with Cisco's Cert Guide official flashcard: "ToS: An 8 bit field where only the first 3 bits, referred to as IP Precedence (IPP), are used for marking, and the rest of the bits are unused."
Source: Adapted from community discussion — msstanick
Refer to the exhibit. Which two commands are required on router R1 to block FTP and allow all other traffic from the Branch 2 network? (Choose two.)
Answer: AC
A. access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp-data access-list 101 permit ip any any B. access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp-data access-list 101 permit ip any any C. interface GigabitEthernet0/0 ip address 10.0.0.1 255.255.255.252 ip access-group 101 out D. access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp access-list 101 permit ip any any E. interface GigabitEthernet0/0 ip address 10.0.101.1 255.255.255.252 ip access-group 101 in
Source: Adapted from community discussion — dragonwise
A company recently decided to use RESTCONF instead of NETCONF, and many of their NETCONF scripts contain the operation <edit-config> (operation="create"). Which RESTCONF operation must be used to replace these statements?
Answer: D
so from https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/prog/configuration/171/b_171_programmability_cg/restconf_protocol.html#id_125840 it is either PUT (create or replace) or POST (create or operation like reload) however looking at the question key wording is that scripts contain the "operation" so from the link answer =>POST
Source: Adapted from community discussion — Dan_T_P
Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page
350-401 practice, question 561. 1003 questions available.
Version 1.0.0. How we source questions