Question 151 · 294 in bank
Refer to the exhibit. Global multicast has been configured for multicast-multicast, but multicast is not functioning on any of the WLANs in the network. Which action enables multicast?
Show answer
Answer: D
300-430ProfessionalCiscoAll questions freePage 16 of 30
300-430 practice questions 151–160
Implementing Cisco Enterprise Wireless Networks (ENWLSI)294 questions across 30 pages are complete and free, with no account or card.
Official study references
294 questions in this bank
Free access · progress saved on this device
Question 152 · 294 in bank
Select 2An engineer configures QoS on an AireOS WLC v8.5. The engineer configures a WLAN for voice traffic and must give a higher priority to WMM clients than to non-WMM clients. Which two configurations should be performed? (Choose two.)
Show answer
Answer: AE
Question 153 · 294 in bank
During discovery, one out of five fabric-enabled WLAN controllers is not being properly discovered. The firewall rules are the same for all the controllers. Which element is missing?
Show answer
Answer: D
Question 154 · 294 in bank
An engineer configures an AireOS WLC v8.2 that has Cisco Aironet 3700 Series APs and Cisco Hyperlocation modules. The engineer deploys and enables a WLAN that has Hyperlocation. During testing, the engineer notices poor location accuracy when the packets arrive. Which action resolves the issue?
Show answer
Answer: C
Explanation
Second this. From the URL above: Troubleshooting HyperLocation Deployment Issues Hardware Poor location accuracy when packets arrive: Ensure NTP server is up and running. Ensure the same NTP server is used for syncing time for WLC, MSE and PI. Ensure that any tilt of APs is recorded accurately within PI maps. Ensure the accurate azimuth angle is recorded within PI. Allow 60-90 minutes for RRM to settle before recording location measurements.
Source: Adapted from community discussion — Supersede
References
Question 155 · 294 in bank
Which Cisco Prime Infrastructure report does an engineer run to troubleshoot client connectivity issues for a VoWiFi network?
Show answer
Answer: B
Explanation
The Traffic Stream Metrics report in Cisco Prime Infrastructure provides detailed information about traffic streams, including metrics related to quality of service (QoS), packet loss, latency, and jitter. These metrics are crucial for evaluating the performance of real-time applications such as voice calls over Wi-Fi.
Source: Adapted from community discussion — robi1020
References
Question 156 · 294 in bank
A company is collecting the requirements for an on-premises event. During the event, a wireless client connected to a dedicated WLAN will run a video application that will need on average 391595179 bits per second to function properly. What is the QoS marking that needs to be applied to that WLAN?
Show answer
Answer: B
References
Question 157 · 294 in bank
An engineer can log in to a WLC but cannot log in to the AP. Which configuration change allows the engineer to log in to the AP without changing the global login policy?
Show answer
Answer: B
Question 158 · 294 in bank
An engineer supports the network infrastructure within a football stadium, and there is a new requirement to send media over wireless. Multicast direct must be used to optimize multicast communication over wireless. Which multicast address must be added in the media stream configuration to meet this requirement?
Show answer
Answer: B
Explanation
n a multicast setup, the video server multicast destination address is the specific multicast group address to which the video streams are sent. When clients subscribe to the video stream, they join this multicast group to receive the stream content. For optimal multicast communication over wireless, multicast direct allows multicast packets to be transmitted directly between the sender (video server) and the receivers (wireless clients/APs) without the need for multicast routers. This helps minimize network congestion and improve efficiency, especially in environments like a football stadium where there might be a high density of wireless clients.
Source: Adapted from community discussion — robi1020
Question 159 · 294 in bank
After the rogue reports from Cisco Prime Infrastructure are reviewed, it is determined that the automatic rogue mitigation is not working as planned. Which security measure must be taken to help prevent rogue APs from being plugged into the network?
Show answer
Answer: A
Question 160 · 294 in bank
Refer to the exhibit. An engineer must identify jammer devices on the wireless network. The AP must scan all configured channels. Which AP mode must be configured to accomplish this?
Show answer
Answer: A
Explanation
In Monitor mode, the access point (AP) continuously scans all configured channels without providing client connectivity. This mode is specifically designed for spectrum analysis, rogue detection, and troubleshooting purposes.
Source: Adapted from community discussion — robi1020
Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page
300-430 practice, question 151. 294 questions available.
About this question bank
Version 1.0.0. How we source questions