300-430 practice questions 141–150

1. Question 141 · 294 in bank

   An engineer needs to configure the infrastructure for wireless clients to use IEEE 802.1X to the onboarding VLAN. After authentication and profiling, it must be determined if the client is a company device that is up-to-date. After this step, the device must connect to the corporate VLAN and access all resources. What must be implemented to meet these requirements?

   • AChange of Authentication
   • BCompletion of Authentication
   • CChange of Authorization
   • DCompletion of Authorization

   Show answer

   Answer: C

   Explanation

   To meet the specified requirements, the engineer needs to implement a process that involves changing the client's authorization after authentication and profiling. Therefore, the correct choice is: C. Change of Authorization The process involves initially onboarding the client to a specific VLAN using IEEE 802.1X authentication. After successful authentication and profiling, the next step is to determine whether the client is a company device that is up-to-date. Once this determination is made, the client's authorization is changed to allow it to connect to the corporate VLAN and access all resources.

   Source: Adapted from community discussion — robi1020

   Next question

2. Question 142 · 294 in bank

   A customer recently upgraded the network to Cisco SD-Access. Cisco DNA Center manages the wireless network; all SSIDs are Fabric-enabled. Cisco DNA Center must be able to classify “Rogue on Wire" APs. Which action must the customer take?

   • AConfigure all access switches to be managed by Cisco DNA Center.
   • BAllow SNMPv3 between Cisco DNA Center and access switches.
   • CConnect APs to the network using a trunk port with native VLAN.
   • DDisable all the DCA channels under RRM on the WLC.

   Show answer

   Answer: A

   Next question

3. Question 143 · 294 in bank

   

   Refer to the exhibit. An enterprise uses 802.11 b/g APs and must track the RFID tags within the network. How many channels must be used to maximize the optimization of the monitoring and tracking of the tags?

   • A1
   • B3
   • C4
   • D11

   Show answer

   Answer: B

   Next question

4. Question 144 · 294 in bank

   Which protocol enables multicast traffic only on a specific WLAN named MULTI123456789 instead of the whole network?

   • AWMM
   • BTPC
   • CDCA
   • DWMF

   Show answer

   Answer: D

   Next question

5. Question 145 · 294 in bank

   A corporation has a wireless network where all access points are configured in FlexConnect. The WLC has a Data WLAN and a VoWiFi WLAN implemented where centrally-switched SSID is configured for the APs. Which QoS configuration must be implemented for the wireless packets to maintain the marking across the wired and wireless network?

   • ASet QoS to Platinum.
   • BEnable CAC.
   • CAllow WMM.
   • DTrust DSCP.

   Show answer

   Answer: D

   Explanation

   D. Trust DSCP. Question is not asking what markings will be applied but what will allow whatever marking there is to exist and be maintained throughout it's journey over both the wired and wireless infrastructure.

   Source: Adapted from community discussion — GoldLeader

   Next question

6. Question 146 · 294 in bank

   An engineer set up RADIUS for WLC management to harden the configuration. Read-only access must be provided to a user. Which Service-Type attribute must be configured on the RADIUS server to meet this requirement?

   • ANAS Prompt
   • BAdministrative
   • CCall Check
   • DCallback Login

   Show answer

   Answer: A

   References

   • Cisco documentation

   Next question

7. Question 147 · 294 in bank

   An administrator receives reports of many interferes in the wireless network and wants to get these interferes' location from the maps in Cisco Prime Infrastructure. When looking at the floor plans/maps, the administrator does not see any interferes but can see all wireless clients located successfully. What must be configured to get the location?

   • AAdd MSE to Cisco Prime Infrastructure and synchronized.
   • BEnable interferer tracking on the MSE.
   • CActivate NMSP communication with the WLC.
   • DConfigure SNMP between Cisco Prime Infrastructure and the WLC.

   Show answer

   Answer: B

   References

   • Cisco documentation

   Next question

8. Question 148 · 294 in bank

   Select 2

   A company has a Cisco wireless network with Cisco ISE. The company wants to allow employees to use their personal mobile devices on the wireless network. The company wants to allow access to the network only if the devices meet certain criteria. To meet the requirement, the company asked a network engineer to create a native supplicant profile. Which two fields must be configured when the profile is created? (Choose two.)

   • AAllowed Protocol (PEAP/TLS)
   • BAllowed Protocol (Ms-CHAPv2/ EAP-FAST)
   • CSSID Name
   • DWLC Name
   • EAllowed Protocol (LEAP/ EAP-TTLS)

   Show answer

   Answer: AC

   References

   • Cisco documentation

   Next question

9. Question 149 · 294 in bank

   Select 2

   An engineer has eight WLCs in a mobility group and must reduce the bandwidth consumed. Which two configuration items achieve this result? (Choose two.)

   • Aglobal multicast mode
   • Bmobility group unicast messaging
   • Cglobal unicast messaging
   • Dmobility group multicast messaging
   • Eglobal symmetric mobility messaging

   Show answer

   Answer: AD

   Next question

10. Question 150 · 294 in bank

    Split Tunneling must be configured for traffic sent by the client to be classified based on packet content, using an ACL. To accomplish this, the packets must be either locally switched from Cisco FlexConnect AP or centrally-switched over CAPWAP. Which type of ACL must be configured to accomplish this switching?

    • AInterface
    • BCPU
    • CFlexConnect
    • DWLAN

    Show answer

    Answer: C

    Next question

Keyboard:J Kmove between questionsA–Dselect an answerRshow or hide the answer← →change page

300-430 practice, question 141. 294 questions available.